1-Chip DLP™ Projectors PT-RQ7 Series

PT-RZ6L

Immersive for all : Compact and Light 1DLP 4K Projectors

View full specifications Share page

Key features of PT-RZ6L

Key features

Making lmmersive 4K Visuals Accessible

Compact Design for an Effortless Workflow

Stable, Reliable, and Efficient Projection

PT-RQ7L	PT-RQ6L	PT-RZ7L	PT-RZ6L
7,500 lm² / 7,500 lm (ANSI)³ / 7,700 lm (Center)⁴	6,500 lm² / 6,500 lm (ANSI)³ / 6,700 lm (Center)⁴	7,500 lm² / 7,500 lm (ANSI)³ / 7,700 lm (Center)⁴	6,500 lm² / 6,500 lm (ANSI)³ / 6,700 lm (Center)⁴
4K (3840 x 2160 pixels)⁵	4K (3840 x 2160 pixels)⁵	WUXGA (1920 x 1200 pixels)	WUXGA (1920 x 1200 pixels)

_{1 PT-RQ7L/RQ6L only.}
_{2 When ET-DLE170 is attached. Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118: 2020 international standards. Value is the average of all products when shipped.}
_{3 Measurement, measuring conditions, and method of notation all comply with American National Standards Institute standards. Value is the average of all products when shipped.}
_{4 Average light-output value of all shipped products measured at the center of the screen in NORMAL Mode.}
_{5 Maximum physical resolution of 4K (3840 x 2160) with Quad Pixel Drive [ON].}
_{6 PT-RQ7L/RQ6L only. Supports input signals up to 1080p. The display frame rate corresponds to the input signal frame rate. When using the PT-RQ7L/RQ6L to display 1080/100p, 1080/120p, or 1080/240p content, edge blending and geometric adjustment cannot be used.}
_{7 Input signals to the PT-RZ7L/RZ6L are converted to the projector’s display resolution upon playback. YPBPR 4:2:0 format only for 4K/60p and 4K/50p signals input via DIGITAL LINK.}
_{8 PT-RQ7L/RQ6L only. Optional ET-SWR10 Real-Time Tracking Projection-Mapping System is sold separately.}
_{9 Optional proprietary and third-party function boards compatible with the Intel^® SDM standard-compatible SLOT are sold separately. Panasonic cannot guarantee the operation of third-party devices.}
_{10 The Dust Protected performance of this unit is not guaranteed to be free from damage or failure under all conditions (environment with conductive dust, etc.). Please use an enclosure in environments with smoke containing oil, salt, and moisture.}
_{11 Around this time, the light output will have decreased by approximately 50 %. IEC62087: 2008 Broadcast Contents, [NORMAL] Mode, [PICTURE MODE] set to [DYNAMIC], Dynamic Contrast [3], temperature 35 °C (95 °F), elevation 700 m (2,297 ft) with 0.15 mg/m³ of airborne particulate matter. Panasonic recommends a checkup at the point of purchase after about 20,000 hours. Light-source lifetime may be reduced depending on environmental conditions. Replacement of parts other than the light source may be required in a shorter period. Estimated maintenance time varies depending on the environment.}
_{12 By weight of the total mass of plastic parts in the projector main unit. Excludes projection lenses, printed circuit boards, labels, cables, connectors, electronic components, color sensor cases, optical components, ESD components, EMI component adhesives, and coatings.}

Specifications of PT-RZ6L

Specifications table

Projector type	1-Chip DLP^TM projector
Display method	DLP^TM chip x 1, DLP^TM projection system
Display Device -> Panel size	17.0 mm (0.67 in) diagonal (16:10 aspect ratio)
Display Device -> Number of pixels	2,304,000 (1920 x 1200 pixels)
Light source	Laser diode
Light output	6,500 lm
Light output (ANSI)	6,500 lm
Light output (Center)^1^2	PT-RQ7L/RZ7L : 7,700 lm PT-RQ6L/RZ6L : 6,700 lm

View full specifications

Brackets

ET-PKD130H

High ceiling mount bracket with 6-axis adjustment mechanism

View product

Brackets

ET-PKD130B

Bracket assembly

View product

Brackets

ET-PKD120H

High ceiling mount bracket

View product

Brackets

ET-PKD120S

Low ceiling mount bracket

View product

Showing 4 of 4

Lenses for 1-Chip DLP

ET-DLE020（for 1-Chip DLP™ Laser Projectors）

Zero Offset Ultra Short Throw Zoom Lens

View product

Lenses for 1-Chip DLP

ET-DLE060

View product

Lenses for 1-Chip DLP

ET-DLE170

1.7-2.4:1 throw ratio (WUXGA)

View product

Lenses for 1-Chip DLP

ET-DLE085

0.8-1.0:1 throw ratio (WUXGA)

View product

Lenses for 1-Chip DLP

ET-DLE150

1.3-1.9:1 throw ratio (WUXGA)

View product

Lenses for 1-Chip DLP

ET-DLE250

2.3-3.6:1 throw ratio (WUXGA)

View product

Lenses for 1-Chip DLP

ET-DLE350

3.6-5.4:1 throw ratio (WUXGA)

View product

Lenses for 1-Chip DLP

ET-DLE450

5.4-8.6:1 throw ratio (WUXGA)

View product

Showing 8 of 10

Related resources

View in Downloads

Brochures

Chọn tất cả

PT-RQ7_Series_pre_en_1717035793.6358

Tải về

Sorry there was an error...
The files you selected could not be downloaded as they do not exist.

You selected items.
Continue to select additional items or download selected items together as a zip file.

You selected 1 item.
Continue to select additional items or download the selected item directly.

Download selected file

Full specifications

Download specifications

Projector type	1-Chip DLP^TM projector
Display method	DLP^TM chip x 1, DLP^TM projection system
Display Device -> Panel size	17.0 mm (0.67 in) diagonal (16:10 aspect ratio)
Display Device -> Number of pixels	2,304,000 (1920 x 1200 pixels)
Light source	Laser diode
Light output	6,500 lm
Light output (ANSI)	6,500 lm
Light output (Center)^1^2	PT-RQ7L/RZ7L : 7,700 lm PT-RQ6L/RZ6L : 6,700 lm
Time until light output declines to 50 % -> NORMAL	20,000 hours [NORMAL]
Time until light output declines to 50 % -> ECO	24,000 hours [ECO]
Time until light output declines to 50 % -> QUIET	20,000 hours [QUIET]
Resolution	WUXGA (1920 x 1200 pixels)
Contrast Ratio (typ.)	15,000:1 (Full On/Full Off, Dynamic Contrast [3]) (TBD)
Screen size (diagonal)	1.27–5.08 m (50–200 in) with ET-DLE055, 1.27–15.24 m (50–600 in) with ET-DLE060/ET-DLE085/ET-DLE105/ET-DLE150/ET-DLE170/ET-DLE250/ET-DLE350, 2.54–8.89 m (100–350 in) with ET-DLE035, 2.54–10.16 m (100–400 in) with ET-DLE020
Center-to-corner zone ratio	90%
Lens	Optional (no lens included with this model)
Lens shift -> Vertical(from center of screen)	+50 %, -16 % (with ET-DLE020/ET-DLE085/ET-DLE105/ET-DLE150/ET-DLE170/ET-DLE250/ET-DLE350/ET-DLE450), +40 %, -16 % (with ET-DLE060) (TBD)
Lens shift -> Horizontal(from center of screen)	+30 %, -10 % (with ET-DLE150/ET-DLE170/ET-DLE250/ET-DLE350/ET-DLE450); +28 %, -10 % (with ET-DLE085/ET-DLE105); +19 %, -10 % (with ET-DLE060); +10 %, -20 % (with ET-DLE020) (TBD)
Keystone correction range	(TBD)
Installation	Ceiling/floor, front/rear, free 360-degree installation
Terminals -> HDMI^™ IN	HDMI^TM x 2 (Deep Color, compatible with HDCP 2.3, 4K/60p signal input*5)
Terminals -> SERIAL IN	D-sub 9-pin (female) x 1 for external control (RS-232C compliant)
Terminals -> SERIAL OUT	D-sub 9-pin (male) x 1 for link control (RS-232C compliant)
Terminals -> REMOTE 1 IN	M3 stereo mini-jack x 1 for wired remote control
Terminals -> REMOTE 1 OUT	M3 stereo mini-jack x 1 for link control (for wired remote control)
Terminals -> DIGITAL LINK IN / LAN	RJ-45 x 1 for network and DIGITAL LINK connection (video/network/serial control) (HDBaseT^TM compliant), 100Base-TX (Compatible with PJLink^TM [Class 2], Art-Net, HDCP 2.3, Deep Color, 4K/60p5 6 signal input)
Terminals -> LAN	RJ-45 x 1 for network connection, PJLink^TM (Class 2) compatible, 10Base-T/100Base-TX, Art-Net compatible
Terminals -> DC OUT	USB Type A x 1 (for power supply, DC 5 V, 2 A)
Terminals -> USB TYPE A	USB connector (Type A) x 1 for optional AJ-WM50 Series Wireless Module/USB memory (dual-use with DC OUT terminal)
Terminals -> SLOT	Open slot for function boards, Intel® SDM standard SLOT-compatible
Protocol versions	IPv4, IPv6*7
Power supply	AC 100–240 V, 50/60 Hz
Maximum power consumption	620 W (6.3–2.7 A) (630 VA) (TBD)
On-mode power consumption(Operating mode) -> Normal	[NORMAL] 470 W (TBD)
On-mode power consumption(Operating mode) -> Eco	[ECO] 340 W (TBD)
On-mode power consumption(Operating mode) -> Quiet	[QUIET] 335 W (TBD)
Cabinet materials	Molded plastic
Filter	No
Operation noise -> Normal	35 dB [NORMAL] (TBD)
Operation noise -> Eco	35 dB [ECO] (TBD)
Operation noise -> Quiet	32 dB [QUIET] (TBD)
Dimensions (W x H x D)	Approx. 498 x 170 x 440 mm (19 19/32˝ x 6 11/16˝ x 17 5/16˝) (With legs at shortest position, excluding protruding parts)
Dimensions (W x H x D) -> Width (not including protruding parts)	498 mm (19 19/32˝)
Dimensions -> Height (including protruding parts)	170 mm (6 11/16˝)
Dimensions -> Depth (not including protruding parts)	440 mm (17 5/16˝ )
Weight	18.0 kg (39.7 lbs) or less (TBD)
Operating environment -> Operating temperature	0–45 °C (32–113 °F)
Operating Environment -> Operating humidity (No condensation)	10–80 % (no condensation)
Applicable software	Multi Monitoring & Control Software, Projector Network Setup Software, Real-Time Tracking Projection-Mapping System*11, Geometry Manager Pro, Smart Projector Control for iOS/Android^TM
Control function via LAN	Crestron Connected^TM V2, Crestron XiO Cloud^TM, Art-Net DMX, AMX® DD, and PJLink^TM (Class 2)
Footnote Description	When ET-DLE170 is attached. When [PICTURE MODE] is set to [DYNAMIC] and [LIGHT POWER] is set to [NORMAL]. Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118: 2020 international standards. Value is the average of all products when shipped. Measurement, measuring conditions, and method of notation all comply with American National Standards Institute standards. Value is the average of all products when shipped. Average light-output value of all shipped products measured at the center of the screen. Around this time, light output will have decreased by approximately 50 %. IEC62087: 2008 Broadcast Contents, Dynamic Contrast [3], temperature 35 °C (95 °F), elevation 700 m (2,297 ft), with0.15 mg/m3 of airborne particulate matter. The estimated time until light output declines to 50 % varies depending on the environment. Cannot be used when ET-DLE035 is installed. Supports YPBPR 4:2:0 format only for 4K/60p and 4K/50p signals input via DIGITAL LINK. Optional AJ-WM50 Series Wireless Module is not compatible with IPv6. Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118: 2020 international standards. On-mode power consumption measured at 25 °C (77 °F) operating temperature at an altitude of 700 m (2,297 ft). Average value. May differ depending on the actual unit. When the optional AJ-WM50 Series wireless module is attached, the operating temperature range becomes 0–40 °C (32–104 °F). Note that the projector cannot be used at altitudes 4,200 m(13,780 ft) or higher above sea level. In the following operating environments, light output may be reduced to protect the projector: when the projector is used at altitudes below 1,400 m (4,593 ft) and ambient temperature is 35 °C (95 °F) or higher; when the projector is used at altitudes between 1,400 m (4,593 ft) and 2,700 m (8,858 ft) exclusive and ambient temperature is 30 °C (86 °F) or higher; and when the projector is used at altitudes between 2,700 m (8,858 ft) and 4,200 m (13,780 ft) exclusive and ambient temperature is 25 °C (77 °F) or higher. PT-RQ7L/RQ6L only. 4K signals are converted to WUXGA (1920 x 1200 pixels) only for the PT-RZ7L/RZ6L.